![]() ![]() For example, the HC2S3-L has a –C cable termination option for connecting it to a CS110 instead of offering an HC2S3-LC model.HA 2015 measures air velocity in five units of measure:, meters per second (m/sec), kilometers per hour (km/hr),feet per minute (ft/min), Miles per hour (Mph)& nautical miles per hour (knots). Note: As newer products are added to our inventory, typically, we will list multiple cable termination options under a single sensor model rather than creating multiple model numbers. ![]() ![]() For example, the 034B is offered as the 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, and 034B-QD.Īll of the other cable termination options, if available, are listed on the Ordering information area of the sensor product page under “Cable Termination Options.” For example, the 034B-L Wind Set is offered with the –CWS, –PT, and –PW options, as shown in the Ordering information area of the 034B-L product page. If a sensor is offered in an –ET, –ETM, –LC, –LQ, or –QD version, that option’s availability is reflected in the sensor model number. The options available for a particular sensor can be checked by looking in two places in the Ordering information area of the sensor product page: Not every sensor has different cable termination options. –PW models terminate with the connector for a PWENC or pre-wired system.–QD models terminate with the connector for a RAWS-F Quick Deployment Station.–ETM models terminate with the connector for an ET107 weather station, but they also include a special system mounting, which is often convenient when purchasing a replacement part.–ET models terminate with the connector for an ET107 weather station.For example, the 034B-ET model designates the sensor as a 034B for an ET107 system. If a cable terminates with a special connector for a unique system, the end of the model number designates which system. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails. The cable length is listed at the end of the Description field in the product’s Ordering information. If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. An –LQ model has a user-specified cable length for connection to a RAWS-P weather station.An –LC model has a user-specified cable length for connection to an ET107, CS110, or retired Metdata1.If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system: Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. Wind speed measurements can be taken and processed with any of the data loggers. The 03101 is read by the PulseCount Instruction in CRBasic and by Instruction 3 (Pulse Count) in Edlog. The 03101 uses one pulse count channel on the data logger. Data loggers compatible with the LLAC4 are the CR200(X)-series (ac signal ≤1 kHz only), CR800, CR850, CR1000, CR3000, and CR5000. The LLAC4 allows data logger control ports to read the anemometer’s ac signals instead of using pulse channels. ![]() For this application, the LLAC4 4-channel Low Level AC Conversion Module can be used to increase the number of anemometers measured by one data logger. Wind Profile StudiesĪn ideal application for the Wind Sentry is wind profile studies. The 03101 can also be mounted to the top of a CM106B or a stainless-steel tripod via the CM216. IPS threaded pipe, which mounts to a crossarm via a CM220 mount or 1049 Nu-Rail fitting. The 03101 anemometer is supplied with a galvanized 10-in.-long x ¾-in. Additional Compatibility Information Mounting ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |